Die-cutting machine with hot foil stamping YOCO JY 76 T

• The 3 sections of the longitudinal hot foil stamping unit can work with foil of 220 mm diameter with enough space for easy operation.
• Setting the roller pressure and foil feed is very easy.
• Max. hot foil stamping speed is 6,000 sheets per hour.
• A servo motor from Japan's Panasonic allows foil to be pulled over a large area at high speed.
• Computer visual control system and operating touch screen for instant display and monitoring of machine status and possible causes of stoppage.
• The servo motor of each roll can be controlled via the PLC, with 3 different settings available.
• The servo motor automatically controls tension and has a special design that automatically drops the pressure if there is a sheet problem or missing sheet.
• A ductile iron frame and a simple foil holder for the respective setting are available.
• 10 independently controlled heating zones with a deviation of ± 1 °C.
• Foil rolls with 1- and 3-inch cores are available.
• The foil holder can be pulled out of the machine thanks to a user-friendly design allowing easy replacement.
• An air-blowing foil separation device and delay device are available for large-format stamping.
• A remaining foil length alarm is available.
• A delay device is available for large-format hot foil stamping.

• Pile table with handle for manual lateral adjustment of the pile during production.
• German-designed non-stop feeder supplied by MMS – Mabeg Machinery (Shanghai) Co., Ltd.
• Feeder system with selectable run at max. 120 sheets per minute.
• 2 suckers for lifting the sheet, 2 suckers for forwarding the sheet.
• The height and angle of the suction devices are easy to adjust.
• Electronic safety devices preventing excessive feeder pile height.
• Micro-adjustment of the lateral position of the pile table is available.
• Double-sheet control.
• Easy change of pull and push side lays by turning a screw, without having to remove and replace the entire device.
• 2 front guides with micro-adjustment and a side guide adjustable with a rotary knob.
• Photoelectric detection device with automatic stop of the feeder table in the event of a paper jam.
• Separate feed controls for the feeder unit and main machine for easy make-ready.
• Programmable logic controller (PLC) and electronic timing control device.

• Maximum unit pressure of 200 t. The required pressure can be set easily on the touchscreen via the electric pressure adjustment system. Digital display of pressure data makes setting up repeat jobs easier.
• The inverter-controlled Siemens main motor enables a maximum speed of 7,000 sheets/h.
• Computerised visual control system and operating touchscreen for instant display and monitoring of machine status and possible causes of stoppage.
• Includes an automatic central lubrication system and automatic lubrication of the main drive chain.
• The die-cutting chase centring system ensures precise setup and reduces changeover time. 5 mm and 4 mm + 1 mm plates are available for repeat jobs.
• Die-cutting chase turnover device and centring system to cut setup time for repeat jobs.
• Specially designed six-piece gripper bar and positioning system with a 2-plate design.
• All drive chains are custom-made in Japan. Each chain has its own serial number and must undergo an intensive pre-stretching process before being shipped to the customer.
• Fitted with a reliable pneumatic brake clutch made in Europe.
• Specially designed top heating system for die-cutting materials such as OPP, PP, PE, PVC, etc.

• Embossing function included as standard.
• The embossing plate is mounted on the honeycomb plate. As the sheet passes through the die-cutting unit, the embossing plate contacts the sheet and applies pressure, producing the final embossed effect.

Creasing

• Creasing function included as standard.
• Depending on sheet thickness, a matrix of the appropriate width and height is fitted to the cutting plate. When the sheet enters the die-cutting unit and comes into contact with the cutting die, the crease is formed.

• Non-stop delivery with wooden pallets.
• Photoelectric safety device preventing various sheet stacking problems.
• Adjustable pressure roller assisting sheet release from the grippers and stacking.
• An automatic auxiliary belt table is available for continuous sheet delivery.
• Feeder movement and speed control can be set on the delivery panel.